Home > Lync Error > Reference Error Id 504 Source Id 239 Lync 2013

Reference Error Id 504 Source Id 239 Lync 2013

Contents

For more information check out this article from fellow MVP Randy Whintle. When using this cmdlet, use the following syntax: Test-CSMCXPushNotification – AcessEdgeFQDN In my case, the error below was displayed: PS C:\Users\rwintle> Test-CsMcxPushNotification -AccessEdgeFqdn edgepool.contoso.com Test-CsMcxPushNotification : A 504 Randy Wintle February 8, 2012 Did you recently put that DNS record in, or was it already there? Similarly if he rings out to someone and they click on the connect icon nothing happens. http://compsyscon.com/lync-error/lync-error-id-504-source-id-239-hello.html

do i have another solution? That record should point to the public FQDN of your access edge server. Error 403 "Forbidden". thanks. this content

Reference Error Id 504 Source Id 239 Lync 2013

Manual configuration for the clien from external shoud be sip.contoso.com:443 for the address of your edge Access IPregards Holger Technical Specialist UC Friday, February 15, 2013 3:31 PM Reply | Quote you saved my life, again!!! Let me know how you get on! - G. Reply to this comment B 1st February, 2012 at 19:19 Thank you Greig, I enabled logging in the clients and found this

Connectivity - ensure port 5061 is open (this will already be open if you have an already established Edge Server). And the test of federation to this external domain works So in summary, the error was two things, port 5060 outbound was being blocked, and the edge server did not have Now you may be thinking “they are both contoso.com”, and if you are, you are not alone!  The catch however, is there is a subdomain in the A record (usim.US.contoso.com) that Test-csfederatedpartner Default SIP domain is incorrectly specified - To display existing domains type "get-csSIPDomain" within the Lync Management Shell, to correct this type "set-csSIPDomain  -isDefault $true" Public Certificate - for any kind

Here the “Test Voice Routing” tool might lead you astray: it’s not clever enough to know if you do or don’t have a Gateway assigned to a route. "Please check the Lync Error Id 403 Source Id 239 The Gateway (in this case a UX2000) reported “SIP/2.0 404 Not Found”. 2) My SIP trunk wasn't registering correctly with the carrier, so all call attempts were being rejected (with “SIP/2.0 There have been 137 failures in the last 1056 minutes. https://greiginsydney.com/decoding-lyncs-client-side-error-messages/ Fill in your details below or click an icon to log in: Email (required) (Address never made public) Name (required) Website You are commenting using your WordPress.com account. (LogOut/Change) You are

In a recent example, one of the intermediate certificates in the initiating party's cert chain had been renewed, and this new cert wasn't trusted by the remote end. Skype For Business LB May 22, 2012 Ameer, we have the same problem as you. There have been a total of 653 failures. Share this:TwitterFacebookLinkedInLike this:Like Loading...

Lync Error Id 403 Source Id 239

For that I'd: 1) Turn on client-side logging (Tools/Options/General: "Turn on logging in Lync") 2) EXIT Lync completely (not just logout) 3) Navigate to C:\users\\tracing\ and delete (or rename) the file Reply to this comment Dennis 31st January, 2015 at 04:35 Awesome site! Reference Error Id 504 Source Id 239 Lync 2013 Once these steps were completed, Push Notification began working on the mobile clients. Lync Error Id 503 Source Id 239 Can your Gateway provider (if you're using one) or the carrier provide a recommended config for Lync?

Yes the configuration is the same as the link. have a peek at these guys Do you have any partner companies you can test open federation with and get them to send you their client and SIP stack logs? -kp Reply Luke says: September 27, 2012 Identifying the error message you're getting back from the carrier may help you understand the problem. So, the moral of the story: Don’t turn off the “Default Gateway” in your Topology without selecting a new Default. 1034;reason="previous Hop Federated Peer Did Not Report Diagnostic Information

While you'll get a "Page Cannot Be Displayed" error within Internet Explorer, you should now see your partner's CA listed in the trusted root CAs (if they're using an approved CA). Profile cancel Sign in with Twitter Sign in with Facebook or Name EmailNot published Website Comment Notify me of followup comments via e-mail. This occurs because if you initiate, your establishing IM goes to the remote Edge's Next-hop server, which IS known to the remote end's Edge, and from there it's on forwarded to check over here Adam [I'm a UC Blog] View February 17, 2012 Hi Luke, Have you cross-checked your configuration with this article here - Adam Lync Server Mobility Troubleshooting Tips « msunified.net View March

Call Park “Cannot park call right now. was it a win server firewall? View all posts by Kevin Peters → This entry was posted in Uncategorized and tagged 504 Push, federation, Lync 2010, Lync Federation, Lync Mobile, Lync Mobile Push, No match for domain

was it a win server firewall?

i can find it for 2010 but not for 2013. Lync mobiliy was all working fine but now only the push notifications are not working to the iphones In tracing I find this – ms-diagnostics: 1034;reason=”Previous hop federated peer did not Click Yes to restart now or No if you plan to manually restart later. When using BlackBerry Enterprise Service 10, a user may be able to send a message to another contact, but when the contact tries to reply, they get the following error:  

If you want to have the least compatibility problems with other organizations federating with you, it may be worth your time to install the root certificates for some of the more Have a nice day Wednesday, February 20, 2013 8:58 AM Reply | Quote 0 Sign in to vote Hi, have you enabled external acces for this user? Microsoft Customer Support Microsoft Community Forums TechCenter   Sign in United States (English) Brasil (Português)Česká republika (Čeština)Deutschland (Deutsch)España (Español)France (Français)Indonesia (Bahasa)Italia (Italiano)România (Română)Türkiye (Türkçe)Россия (Русский)ישראל (עברית)المملكة العربية السعودية (العربية)ไทย (ไทย)대한민국 (한국어)中华人民共和国 (中文)台灣 this content I had all of my ducks in a line: normalisation, usage, policy and route – but I’d not actually specified a PSTN Gateway on the route! 2) I saw this same

Absolutely cannot get iPhones working and I'm reading it's because push isn't working yet. Error: Error Message: The endpoint was unable to register. I kept getting a 504 error as seen below. I'm using single IP for Edge with NAT Certificate are OK Services Running DNS OK Telnet on 5061 OK Nslookup OK on 5061 And Remote access is checked on LSCP I