Page 80 Table 4-1. Simply reverse the layout for a “right-hand take away” requirement. Error Codes and Corrective Action Error Probable Cause Corrective Action Code No POS interface has been selected (Null interface). Page 148 Scale Motion Level Filter — continued Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code check over here
Power-up the scanner/scale. 3. Options for this feature are as follows: • FULL host interf ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.3/ Model 8101, 8201, 8102 and 8202 (Medium Scanner or Scanner/Scale) Cutout Dimensions Models 8101/8201 Window & Models 8102/8202 5.1" 6.2" Dimensions (12.95cm) (15.75cm) 9.1" (23.1cm) 4.125" ± .062 (10.5cm) 15.7" (39.88cm) By buffering data from a bar code, the scanner can continue to read a new bar code while the old one is being transmitted to the host.
RS-232 SASI scale interface supports only U.S.A. PATENTS: 4,709,369 4,749,879 4,792,666 4,798,943 4,799,164 4,861,972 4,861,973 +5V at 2.0A... To set the Maximum Host-Transmitted Message Length: 1. Magellan 8400 Manual F-12 Bookland ......................F-12 Code 39 ......................F-12 Codabar ......................F-13 MSI/Plessey ......................
Page 43 Figure 2-8. Magellan 8500 Error Codes Generated Thu, 01 Dec 2016 03:39:17 GMT by s_ac16 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.4/ Connection See the topic, Configuration Interface Type, in Section 6 to select the required interface using Blinking programming bar codes. Page 132: Good Read Beep Frequency Good Read Beep Frequency Adjusts the scanner’s good read beep to sound at low, medium, or high fre- quency (controls the beeper’s pitch/tone). • Low
If it is configured to do so, the Figure 4-1 4-3 Previous page Next page 1...878889909192939495 Also See for Datalogic Magellan 8500Xt Datalogic Magellan 8500Xt Quick Reference Manual 24 pages Datalogic 8400 To set the EAS Timeout: 1. GOOD READ BEEP VOLUME = MEDIUM LOW GOOD READ BEEP VOLUME = MEDIUM ®... A little planning now will save a lot of frus- tration later. 4.
Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or POS terminal by attempting to change to an incompatible interface. You may be required by state or local law to have these procedures performed by a certified technician or verified by a proper official. Magellan 8200 Service Manual Page 29 Section 2 Site Preparation and Installation This section provides a reference for preparing most checkstands to receive the scanner or scanning-scale. Magellan 8400 Error Codes These designs put less stress on the cashiers’...
Page 73: Vertical Scan Window Replacement Vertical Scan Window Replacement The Vertical Scan Window enclosed in the All Weighs™ Platter is a replaceable part. Figure 1-2. Mount the horizontal surface of the scanner flush with the coun- tertop to encourage slide scanning rather than lifting. 2. Check with local Weights and Measures authorities regarding proper posi- tioning of scale displays used in retail trade. Psc Magellan Sl 384 Manual
Pounds) Once you have completed the calibration sequence, you may be required to perform these step-by-step verification procedures. Pass UPC/EAN bar code labels in front of the scanner’s win- dows. Recalibration/recertification may be required when adding a Remote Display. this content Page 38: Checkstand Preparation, Liquid Spills And Moisture Checkstand Preparation Reference Figure 2-5.
Page 89 Figure 4-7. Magellan 8500 Manual Scan your selection from the bar codes below. Page 149: Scale Led Enable Scale LED Enable This feature enables/disables Scale LED (Yellow LED) operation.
No user maintenance of the system other than cleaning of the scan windows is required. The IBM USB interface provides its own set of options. Page 5: Table Of Contents Operational Maintenance ...................... 3-10 Vertical Scan Window Replacement ............... 3-11 Horizontal Scan Window Replacement (WRG) ............3-13 Power-Up Selftest ....................4-1 Operational Tests ....................4-1 Diagnostic Tests ....................4-2 Diagnostic Magellan 8502 Error Codes Generated Thu, 01 Dec 2016 03:39:17 GMT by s_ac16 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.5/ Connection
The unit scans equally well in either of these two configurations. Page 140: Scale Enable Scale Enable Use this feature to enable or disable scale operation. Page 143: Scale Enforced Zero Return Scale Enforced Zero Return This feature enables/disables the enforced zero return of the scale. Place a 30.0-pound load on the scale and verify that the display shows between 29.99 and 30.01 pounds.
Lift off the platter View the Remote to verify, then set the platter Call Tech Support Display and/or the back into position. Press lightly on the weigh platter of the scanner/scale with one hand and at the same time press and release the Scale Zero Push Button on the operator’s panel. Page 68: Operating Mode, Normal Operation, Sleep Mode • When the scanner or scanner/scale completes its Selftest success- fully, it emits a power-up tone (when configured to do so) and enters Page 167: Global Suffix Global Suffix This feature applies to RS-232 interfaces (Standard, Wincor-Nixdorf, and Single Cable).
Page 146 Scale Interface Type — continued Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you Scan the SWITCH bar code. 2. Page 158: Rs-232 Interface Selection RS-232 Interface Selection Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code Please try the request again.
This filter is generally used only in applications where scale error E_1 (too much motion at power-up) has occurred. To set this feature: 1. Scanning-Scale Nomenclature Weighing Surface — Lean Volume/Tone Push Button Oversize Produce Here Yellow LED Green LED Scale Zero Bonnet Push Button Horizontal Vertical Window Window All Weighs™... Generated Thu, 01 Dec 2016 03:39:17 GMT by s_ac16 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection