Home > Error Codes > Ibm Ts3100 Tape Library Error Codes

Ibm Ts3100 Tape Library Error Codes

Contents

Superuser messages: Fixed Manage Library messages to display the same information for Superuser as for Administrator. The SNMP Trap will stop being generated for the data cartridge once the load count for the cartridge surpasses 49. By using this site, you accept the Terms of Use and Rules of Participation. End of content United StatesHewlett Packard Enterprise International CorporateCorporateAccessibilityCareersContact UsCorporate ResponsibilityEventsHewlett Packard LabsInvestor RelationsLeadershipNewsroomSitemapPartnersPartnersFind a PartnerPartner In the past we received the same error and the autoloader chassis & drive were replaced and this solved the problem. http://compsyscon.com/error-codes/lg-washer-error-codes-oe.html

It's been awhile and all logs now have '0' entries. sub-code indicates which fan is affected. Ensure Domain Name on the Configure Library Network page is the same as the Domain Name on the Configure Library Event Notification page. Thank you, Alex 0 Kudos Reply All Forum Topics Previous Topic Next Topic 1 REPLY Curtis Ballard Honored Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight

Ibm Ts3100 Tape Library Error Codes

If Event Notification is enabled ensure the Domain Name is not blank. Ensure Target IP addresses are consistent with the library network protocol stack. Ensure Target IP addresses are consistent with the library network protocol stack. It does the backup ok but it doesn't change the tape.

Refer to Setup, Operator, and Service Guide (GA32-0545-06, Part Number: 46Y0013). Any other sugestions? By using this site, you accept the Terms of Use and Rules of Participation. End of content United StatesHewlett Packard Enterprise International CorporateCorporateAccessibilityCareersContact UsCorporate ResponsibilityEventsHewlett Packard LabsInvestor RelationsLeadershipNewsroomSitemapPartnersPartnersFind a PartnerPartner Library power cable(s) must be unplugged and re-plugged to restore functionality.

A0 Sled range of motion out of specification NOTE:Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. Ibm Ts3200 Error Codes Use the following procedure when changing library network protocol stack (IPv4 to IPv6, IPv6 to IPv4, or Dual Stack to IPv4): Configure the library network protocol stack and IP addresses with Only use a static IPv6 address if DNS is not configured. Watson Product Search Search None of the above, continue with my search TS3100 / TS3200 Release Notes Fix readme Abstract TS3100 / TS3200 Release Notes Fix List Content IBM TS3100 /

Lib/err 80 F1 01 00 He Drive Communication Error 4.5 out of 5 based on 43 ratings. Error F1 04 4C F1: HE: drive communication error A library reboot resolved the issue. Remove and inspect the magazine or drive for a stuck tape Run the Wellness Test B5 Robotic controller not responding to command from library controller Reset the unit Retry the operation See documentation Save/Restore VPD function has been improved Changed behavior of "Power Off" mechanism Updated documentation on using the Auto Clean option Added warning about moving media across partition boundaries Auto

Ibm Ts3200 Error Codes

When you think of it thoroughly, these will issues will actually assist you know if the computer is having some troubles and needs some care. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c00574301 Niki Lauda offers answer to sparse German crowd puzzle… F1: Daily International News roundup, inside whispers and insight together with thoughts and opinion… ← Previous Post Next Post → If you Ibm Ts3100 Tape Library Error Codes Post navigation Previous PostDisplay Message Box Error VbaNext PostError Saving Object Arcgis Model Builder Search for: Proudly powered by WordPress Work Notes Email:dongdonggeorge#163.com Status:NA 博客园 首页 新随笔 联系 订阅 管理 随笔-314 Anyone ever experience a similar error?

sub-code 00: drive sled #1, sub-code 01: drive sled #2 NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. his comment is here saetechnologies.com - Colorway Wordpress Theme by InkThemes.com TomDownload Search Primary Menu Skip to content Sitemap Search for: Lib/err 80 F1 01 00 He Drive Communication Error admin Lib/err 80 F1 01 Whatever type of operating system you might have, you can�t run away from this issue. It is possible to download the file from the internet so long as it is a system file.

Changed to 15 minutes OCP: Wrong information displayed when no second Drive is installed in 4U Library RMU: Move Media showed wrong Source address and cartridge VOLSER RMU: Cleaning tapes in IBM TS3100 / TS3200 Library Code 6.90 Release Notes September 2008 Component Firmware The following component firmware is required for this release: Library: 6.90 Drives: LTO4 - 8197 (SAS, Fiber, SCSI) Can not disable SNMP after it is enabled or enable SNMP after it is disabled. this contact form I need to keep track on manual moves and slot 42. 15.05.06 09:08:35.66 LIB/ERR<80 8A 4B 15 2B 02 00 00 00 00 00 00 FF 04 02 FF 02 2A

You can do such after you restart your personal computer. Fixed message text when Administrator changes Superuser password. Message text is as follows – "New library detected.

The code 9B is the main error code, and 37 is the error sub-code.

An installation procedure is needed if it�s a software that causes the problem. On the other hand, increasing your pagefile size will do if you think you could still work on your RAM. One that drives, as the operator of a motor vehicle. 2. There are also conditions that may prevent it from being enabled after it is disabled Use the following procedure if problems are encountered when enabling/disabling SNMP: Configure the library network protocol

Follow the order of the areas you should be going: Advanced system settings, Advanced tab and Settings. Reboot library. kingkong.storage.tucson.ibm.com) if DNS is configured on the Configure Library Network page. http://compsyscon.com/error-codes/ducati-error-codes.html But of course, ensure that you are transacting with a reputable service provider.

If Event Notification is enabled ensure the Domain Name is not blank. Action: Assigning IPv6 static addresses to the EKM server IP fields (Configure Library Encryption page) will cause configuration errors if DNS is configured on the Configure Library Network page. A0 Sled range of motion out of specification NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. the new chassis CRU will Pop-up a message on the OCP instructing the user to install the Library Controller Card from the old library.

Event Notification: Fixed problem that existed with the 6.xx firmware. Action: When the Network Protocol Stack is changed from IPv4 to Dual Stack, and SNMP is enabled with a valid IPv6 address, hitting the Submit button may lock the library. Anyone else seen this one? Choosing to troubleshoot the problem on your own is a great thing.

This has been changed to 7 characters (example: 78B0368) to match the serial number label specification. ("S/N PP-SSSSS". Showing results for  Search instead for  Do you mean  Menu Categories Solutions IT Transformation Internet of Things Topics Big Data Cloud Security Infrastructure Strategy and Technology Products Cloud Integrated Systems Networking