Home > Error Code > How To Fix Dr Code On Hot Tub

How To Fix Dr Code On Hot Tub

Contents

Sunspa Monaco in the garden since March 2011. Alvin Shepherd 7.103 görüntüleme 7:57 # 27 Hot Tub Heater Replacement for 240 volt hot tubs. - Süre: 6:27. PLEAS HELP!! WARNING, if you go too far the pressure switch may activate with the pump off. have a peek here

Press any button to reset after the problem has been corrected, or or contact your Dealer or Service Organization. 1. Learn more You're viewing YouTube in Turkish. Daha fazla göster Dil: Türkçe İçerik konumu: Türkiye Kısıtlı Mod Kapalı Geçmiş Yardım Yükleniyor... It may be possible for the stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first. http://en.allexperts.com/q/Hot-Tubs-3536/2008/6/Hot-Tub-dr-error.htm

How To Fix Dr Code On Hot Tub

So check this all out and see what you come up with or call in a local tech to check the pump out. auto resource 18.291 görüntüleme 4:52 How to Diagnose and Repair Your Hot Tub Heater | Arctic Spas - Süre: 9:09. In this case, if the extreme conditions are determined, the spa will display the StU message until the spa is shut down It will also set the HOt flag (HOt does Is the pump works correctly ?

If the problem continues contact the dealer. Product Technical Support Help Me Replace A Part Product Manuals Product Color Codes Spa Panel Messages Topside Panel Manuals Common Spa Problems System Cross Reference Home>Balboa Spa Panel Messages Balboa Common Perhaps there is hair or debris caught in the impellar that is restricting the flow of water or possibly the motor is just defective. Hot Tub Error Code Dry Back to Top drn or DRAINING Message While in Standby Mode, "Drain" (drn) Mode has been Activated.The "Jets 1" Button has been Pressed while in the Standby Mode, and Pump 1

Also, the Pumps won't go on. The fundamental reason is water flow through the spa control system, if the water is not flowing at a rate to satisfy the pressure switch, it will result in one of Credentials confirmed by a Fortune 500 verification firm. https://www.poolandspacentre.co.uk/help/hot-tub-and-spa-error-codes.html Select "Message Other than rtC or RTC FAILURE" Below.

Add pH Increaser according to Manufacturers Instructions.Note: If you do Not have a pH Sensor installed in the Spa System, you should Never get this Message. What Does Dr Mean On A Hot Tub But hold on to the link for the manual. For information regarding repairs click here.If your spa is not overheating and you are getting the above error codes then a couple of things could be happening. Flow switches are plumbed in line with the plumbing.

Leisure Bay Spa Error Codes

Make sure the temperature sensor is fully inserted into the sensor fitting on the heater. http://www.spadepot.com/spa-error-codes.htm The Water Temperature is Always maintained within 1°F (.5°C) of Set Temperature. How To Fix Dr Code On Hot Tub Ask an Expert Online. Balboa Hot Tub Error Codes Test and Adjust Sanitizer Level per Manufacturers Instructions.

This indicates a Problem with the Firmware (Operation Program), or the System is Operating on Unreleased Firmware (Sample or Prototype System). navigate here If there is Now an Error Message, select Message Other than rtC or RTC FAILURE below.No Error Messages3. covers error codes hot tub leisure bay spas owners manual Share This Previous Post← Beachcomber Hot Tubs Error Codes & Information Beachcomber Hot Tubs Error Codes & Information Next PostHow to Once the spa cools down to 107°F, the tub should reset on its own. How To Fix Flo Error Hot Tub

About UsTell FriendsHow to AskHow to VolunteerFAQTech SupportTop ExpertsExpert LoginBrowse Answers:By CategoryAlphabeticallyFind expert answers to:Find This site uses cookies. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different. On the subsequent power-ups, the GFCI test is skipped because the proper flag has been set in the software.Note: The GFCI Test Feature should only be Enabled in the United States Check This Out Heat Related Pump Not Primed.

All Automatic Functions Remain OFF during this time. Vita Spa Error Codes Doing so may cause damage to the pump and cause the system to go into an overheat condition.If after repeated attempts (hours apart) you still cannot get all pumps to prime, If the spa is left in this state, no user functions will operate, but Freeze Protection remains active.Cycling the power will clear the gFI fault and run the test again.Once a

Dilinizi seçin.

softcellelectrical 49.399 görüntüleme 4:15 How To Diagnose and Repair Hot Spring Spa - Süre: 4:52. pump is running and pulling water down through the filters. The Celebrity series has the following five models to choose from the Tonga, Santo, Hilo, Adirondack, and Galaxy.The Cover Guy custom makes replacement Leisure Bay Spas hot tub covers for all of Marquis Spa Error Codes Back to Top DETAILED PRIMING INSTRUCTIONS In Priming Mode, Nothing turns on Automatically*.*Note: On the VS/GS Model, the Circ Pump will be on, and on some EL/GL Models, a continuous filtration

Email Address: Bath/Spa Professionals Homeowners Home | Contact Us | About Us | My Account | Shipping Policy | Return Policy | Privacy Policy | Terms & Conditions | Cannot Find Press "Mode" Button to Clear Message. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. this contact form Either wait for the Potential Freeze Condition to End, or contact your Dealer or Service Organization.

How does one fix this issue? If water level is okay, check to see if the pumps are primed. Closed Slice Valve.7. Therefore, "OHH" is considered to be a Flow Related Error.Check for All of the following Conditions:1.

characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 426 10258782 Login|Contact Us Pool and Spa Questions about Pool Repair? From that we can determine the spa pack that the spa has and should be able to find more operating information from the manufacturer (Balboa or other, each spa and spa As far as filling the tub, I did place the garden hose into the filter directly to minimize the possibility of air lock. If the hot tub does not reset, turn off the power to the spa and call your dealer or service company.         IC"Ice" - This is a Potential freeze condition detectedNo

Back to Top rCO or CLEAN COVER Message Time to Clean "Cover Reminder" (rCO).Appears Every 180 Days*. Thanks again! Clean and Condition Wood per Manufacturers Instructions. I've been 11/26/2016 11/26/2016 dontrudeau I went to take a dip this morning and there is no power in 11/26/2016 11/26/2016 billyjr1961 I have an older Arctic Spa with a Gecko