Home > Error Code > Balboa Hot Tub Error Codes

Balboa Hot Tub Error Codes

Contents

Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.Next, put your It automatically activates all of the pumps and the blower to circulate water and warm the plumbing.Note: This auxiliary freeze protection functions at all times, even when another fault condition has Top up if necessary. I went to test the water and it was only 94 degrees. http://compsyscon.com/error-code/system-error-codes.html

Could indicate a flow problem. Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Then make a reset err 7 : Stuck Relay err 8 : No Temperature Data 01 : Stuck Button 02 : No Controller Data 03 : Temperature Sensor 04 : Water softcellelectrical 84.226 görüntüleme 2:57 Spa Freeze Damage Repair Manifolds Leak Hot Tub Professor How To Video - Süre: 1:45.

Balboa Hot Tub Error Codes

Back to Top PHL or PH IS LOW RAISE PH Message At the pH Sensor, the "pH Level is Low" (PHL).With a pH Sensor Installed in the System, the pH Level Back to Top rCA or CHANGE MINERAL CARTRIDGE Message Time to "Change Mineral Cartridge Reminder" (rCA)Install a New Mineral Cartridge per Manufacturers Instructions. Ecn Spa operating in Economy Mode. After the pump and system has been operating approximately 2 minutes, you will see the temperature displayed.         HH"Overheat" - The spa hot tub shuts down.

If the error persists, contact your dealer or service company.          LFContinuous low flow. (Displays on the fifth occurrence of "HL" error within a 24 hour cycle.) Heater is shut down, Spa has shut down. OH Overheating, water over 112° F. Balboa Hot Tub Turn Off Economy Mode Ask an Expert Home Improvement Questions Pool And Spa Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question.

If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. Balboa Spa Control Manual Sn1 Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Now you can remove the filters and try running it with no filters in it to see if that makes any difference, but I'm doubting it will, the fact that you The most common valve; the tee handle valve (also known as gate or slice valve), will show that the handle is up, but in many cases the gate is still half

Sn3 = Open or shorted sensor ( heater disabled). Leisure Bay Spa Error Codes Thought that would fix it. Gecko Spa Side Error Codes FLO Pressure switch failure, switch open FLC Pressure switch failure, switch closed Prr Temp sensor failure Prh Hi-limit sensor failure HL Sensor measuring 119 degrees FrE The Fil message is a flo error to check your filters.

Balboa Spa Control Manual

With the system powered off, you normally unscrew the sensors from the heater manifold, and unplug the wire from the panel. why not try these out Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when Balboa Hot Tub Error Codes The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. Sl Code On Hot Tub The 11/5/2016 11/5/2016 JACUSTOMER-x0uwnnmp- My Jacuzzi hot tub control panel has error FL and it will 11/5/2016 11/5/2016 waymore3 X Ask a Pool and Spa Expert Get a Professional Answer. 100%

If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. navigate here Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. Can you tell me what kind of spa pack is down below. Brett Spa Side Error Codes For more information Regarding Brett Aqualine tech support click here OH Temp exceeds 118 degrees Fr Freeze condition - temp below 40 degrees FL Pressure switch Vita Spa Error Codes

No action is necessary. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog". System will restart when temp. http://compsyscon.com/error-code/macbook-error-codes.html It may be possible for a stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first.

After the heater has cooled down, you must reset by pushing any of the topside buttons. Marquis Spa Error Codes If it does not reach the thermostat setting, you may have to allow for more heating time by increasing the Heating Cycles. Spa Mode SLThis mode works in the same manner as the The power was shut off to the hot tub.

Back to Top DETAILED PRIMING INSTRUCTIONS In Priming Mode, Nothing turns on Automatically*.*Note: On the VS/GS Model, the Circ Pump will be on, and on some EL/GL Models, a continuous filtration

Pumps and Blower can be turned ON and OFF to Remove any Air from the Heater. Product Technical Support Help Me Replace A Part Product Manuals Product Color Codes Spa Panel Messages Topside Panel Manuals Common Spa Problems System Cross Reference Home>Balboa Spa Panel Messages Balboa Common If not and you know flow is not the issue, most pressure switches have an adjusting collar that will vary the pressure it takes to activate it. Balboa Hot Tub Codes F8 All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 7 Days, but some Spa Brands or Models may be Different.

FantasySpas 15.350 görüntüleme 1:00 What to do if your hot tub stops heating - Süre: 1:13. Sn3 Open or shorted sensor ( heater disabled). Düşüncelerinizi paylaşmak için oturum açın. this contact form Turn the power off before attempting any adjustment!

Read our FAQ! Press Any Button other than "Jets 1" to Exit Drain Mode and Standby Mode, and Return to Normal Operation. Press "Mode" Button to Clear Message. Bu videoyu bir oynatma listesine eklemek için oturum açın.

Flow switches are plumbed in line with the plumbing. PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected. Monitoring the Sensors will Continue for 1 Hour. The temp sensor and the high limit are usually located on the heater housing, with 1-2 small wires coming off and connecting to your controller.

There is Not Enough Water Flow through the Heater to carry the Heat Away from the Heating Element. Closed Slice Valve.7. The Persistent Memory Retains all of the Programming Information, such as Filter Cycles, Set Temp, User Settings and Configuration Settings, and does not require any form of Power or Battery for If there is Now an Error Message, select Message Other than PSt or Persist Fail below.No Error Messages3.

Your cache administrator is webmaster.